How to Move Arbitrum USDC to Base and Confirm It
How to move USDC to Base network from Arbitrum: use Jumper bridge to compare routes, approve the transfer, and confirm USDC appears in your Base wallet.
The Aeterna Sol Editors

One bridge step moves your USDC from Arbitrum to Base, where you can confirm the balance in your wallet. Since both networks have native Circle USDC and use ETH for gas, you can send USDC directly without swapping it for another token. In Jumper bridge, set Arbitrum as the source and Base as the destination, then compare how much each route says you will receive.
What to have ready
To start, you need USDC and ETH on Arbitrum, plus a wallet with Base added. ETH pays the transaction gas on Arbitrum; you will also use ETH for gas if you later transact on Base. Keep enough USDC in your wallet for the transfer amount you plan to enter.
Circle issues native USDC on both Arbitrum and Base. Select the USDC token associated with each network when choosing the source and destination. If you hold a different token with a similar name, pause and confirm its network and token details before proceeding.
Have your wallet connected to the network where the USDC currently sits. You can switch networks when the wallet or bridge prompts you. Before approving a transaction, read the wallet prompt and make sure the token and amount match the transfer you intend to make.
Which route should you choose?
Choose the route with the highest quoted amount received for your transfer. A bridge aggregator such as Jumper bridge brings together routes from different bridge and swap services, so the available quote can vary with the amount, liquidity, fees, and route conditions.
Circle CCTP moves native USDC by burning it on Arbitrum and minting USDC on Base. The burn-and-mint mechanism transfers the native token between supported chains at a 1:1 token amount, before any applicable route charges. Because the token amount does not depend on a pool’s available inventory, a CCTP route can be useful when you are moving a larger balance. Compare its quoted receive amount with other available routes.
A relayer route, such as Across Protocol, works differently. A relayer can fill the transfer from funds it already has on Base, then settle and rebalance later. That can deliver USDC faster than waiting for a burn-and-mint transfer to complete, while the quote may account for fees and available liquidity. As the transfer amount grows, a pool or relayer route can quote a lower amount received than CCTP. The displayed quote helps you weigh the amount against the estimated speed.
Route availability, timing, and quoted amounts can change. Compare the options shown for your specific transfer rather than assuming one method will always be fastest or deliver the most. If the route details or receive amount look different from what you expect, review the selection before approving.
How to send USDC to Base
Follow these steps to send USDC from your wallet on Arbitrum and confirm receipt on Base.
- Connect your wallet in Jumper bridge. The page should show your connected wallet address; confirm it is the wallet holding your Arbitrum USDC.
- Choose Arbitrum USDC as the source and Base USDC as the destination. The route panel should show those networks and tokens in the correct order.
- Enter the amount, then compare the available routes by quoted amount received. Review the route’s estimated timing and fees as well. The selected quote should show how much USDC is expected to arrive on Base.
- Approve USDC when your wallet requests permission. The wallet should display an approval transaction for the token; check the details and submit it. If the wallet requests a separate approval before the transfer, wait for it to complete.
- Confirm the transfer in your wallet. You should see a transaction submitted on Arbitrum, followed by a route status or completion update. Wait for the transfer to finish before treating the quoted destination amount as received.
- Switch your wallet to Base and view the USDC balance. When the balance appears on Base, the transfer is complete.
If the Base balance does not appear immediately, check the route’s transfer status and confirm the wallet is displaying Base. A relayer route may show its fill before later settlement, while a CCTP transfer must complete its burn-and-mint process. The transfer status helps you distinguish a pending bridge from a missing wallet balance.
Confirm the USDC arrived
The transfer is done when USDC appears in the connected wallet on Base. A completed source transaction on Arbitrum shows that your transfer was submitted, but the destination balance is the practical confirmation that the funds arrived.
Using Jumper bridge lets you compare CCTP and relayer quotes for the amount you are sending, so you can choose between a native burn-and-mint transfer and a potentially faster pool fill. Since both chains support native USDC, your choice comes down to the quoted amount, fees, and estimated timing for this transfer.
With native USDC on both networks, one direct bridge transfer gets your balance onto Base. Compare the routes for your amount, approve and confirm the Arbitrum transaction, then finish by checking the USDC balance on Base.